STM Powersports 2010-2019 Can-Am Commander Rage 3RS Primary Clutch

STM Powersports 2010-2019 Can-Am Commander Rage 3RS Primary Clutch

STM Powersports 2010-2019 Can-Am Commander Rage 8 Primary Clutch

STM Powersports 2010-2019 Can-Am Commander Rage 8 Primary Clutch

STM Powersports 2010-2019 Can-Am Commander Rage 6RS Primary Clutch

CanAmSTM Powersports
  • The cover is designed to use Polaris ATV springs which provides a wide variety of spring rates to choose from.
  • We offer the Rage 6 calibrated with a spring and set of our own adjustable SUPERTIP CAM ARMS.
  • Comes with a belt removal tool and bolt for installation.
  • Each clutch is assembled and setup to run the BRP OEM belt.
  • We have tested setups for your particular application. You bolt it on and GO!
SKU
STM-6RS-com-3001093
$1,831.00
Free Shipping to the lower 48 US States

Maximum 400 characters

 

New improved two-way bearing design. The main shaft bearing is now smaller with a 47mm outside diameter allowing a lower initial takeoff ratio than our past design. Allows tighter belt deflection and smoother transmission shifting.

All new unique design that will hold the belt on high horsepower applications. The concept of this design is to provide an improved amount of force to the belt approximately for the first ½ to ¾ of the belts shift and then release the force, once the vehicles momentum is established. This design solves the biggest problem that all racers face from years past-- belt slip and over revving during hard acceleration. Problem solved, Hang on! The way it works: All cam arms engage at the same time providing over twice the amount of force to the belt. Once the movable sheave has shifted ½ to ¾ of its now adjustable shift the supplemental cam arms sign off due to centrifugal force that holds them suspended above the movable sheaves rollers. This allows the main cam arms to finish the shift and acquire the proper operating rpm. We can now change and control the total shift in two ways. First is by adding more mass to the supplemental arms and secondly by changing the supplemental roller diameters. Yes, it's that simple. By decreasing the roller diameter the supplemental arms let go of the shift earlier and by increasing the roller diameter the supplemental arms shift longer before release. During testing we discovered that by increasing the roller diameter by .125" at one time, the initial over revving during hard acceleration would drop 500 rpm with no change in engagement rpm. This option is so simple but yet effective by just a 10 minute roller change. Uses any cam arm available on the market utilizing our retrofit pin design. The first stage cam arms will be provided with the Rage (second stage cam arms sold separately). They will be capable of adding additional weight for adjusting that killer hole shot. A set of three different size rollers will be provided.

The cover is designed to use Polaris ATV springs which provides a wide variety of spring rates to choose from.

We offer the Rage 6 calibrated with a spring and set of our own adjustable SUPERTIP CAM ARMS.

Comes with a belt removal tool and bolt for installation.

Each clutch is assembled and setup to run the BRP OEM belt.

We have tested setups for your particular application. You bolt it on and GO!

DUE TO OFFSET DIFFERENCES THE RAGE PRIMARY HAS TO BE USED WITH THE 302BATVD SHORT POST TUNER DRIVEN AND THE LONG POST WITH THE STOCK PRIMARY.

Item numbers 1001649 Primary Clutch Vice Holding Tool or 1001653 STM Spider Nut 1-7/16" Extra Deep Socket 6 Point and either 1001020 STM Rage 3 & 6 Spider Tool, or 1001032 STM Rage 4 & 8 Spider Tool (depending rage number) is required when removing or installing the spider. Works on all STM primary clutches. Sold separately.

When ordering use this guide to help you pick options

Choose Rage # - This is what rage clutch you want, Rage 3 your basic replacement clutch, Rage 6 is most popular dual stage clutch that will handle most applications even low boost turbo, Rage 8 is for higher HP applications that require heavy cam arms.

Conversion Kit - You will choose the 1001321 when running the STM weights.

Choose Engine HP – Let us know about your bike - Is it naturally aspirated/stock? Big Bore Kit? Does it have a turbo? If you choose turbo-how much boost? This gives us an idea of how to set the weights up. KEEP IN MIND WE CAN ONLY GET YOU CLOSE WITH WEIGHT SET UP. Everyone's riding style is different so it’s up to the customer to do the fine tuning!

More Information
Shop by Manufacturer CanAm
Shop by Brand STM Powersports
Write Your Own Review
You're reviewing:STM Powersports 2010-2019 Can-Am Commander Rage 6RS Primary Clutch
Your Rating
All items ship within 24-48 business hours or you will be contacted.  All shipments will arrive UPS or FedEx ground, select shipments will arrive USPS.  All shipments over $150.00 USD will be free to the lower 48 US States.
Returns accepted within 30 days of the original purchase receipt.  Any item shipped and not defect or have a mistake on our part will incur a restocking fee and cover return shipping.  The restocking fee would be deducted from your refund.
Search engine powered by ElasticSuite